 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| the information in this document is subject to change without notice. please confirm with the delivery specification before starting to design the system. tft color lcd module nl10276ac28-02l document no. en0456ej1v0ds00 (1st edition) date published december 1999 p printed in japan 36 cm (14.1 inches), 1024 768 pixels, full-color, ultra-wide viewing angle, multi-scan function, crt interface board data sheet 1999 description nl10276ac28-02l is a tft (thin film transistor) active matrix color liquid crystal display (lcd) comprising amorphous silicon tft attached to each signal electrode, a driving circuit, a crt interface board and a backlight. nl10276ac28-02l has a built-in backlight with an inverter. the 36 cm (14.1 inches) diagonal display area contains 1024 768 pixels and can display full-color (more than 16 million colors simultaneously). also, it has ultra wide viewing angle and multi-scan function. therefore, we call this module super fine tft. features ? ultra-wide viewing angle and low reflection ? crt interface board auto recognition of input signal: analog rgb signals, synchronous signals (hsync, vsyn, composite) digital control: e.g. brightness, display position free supply voltage sequence corresponding to ddci and ddc2b corresponding to vesa dpms ? multi-scan function: e.g. xga, sxga, xga, svga, vga, vga-text, mac ? incorporated edge type backlight (four lamps into two lamp holders, inverter) ? lamp unit replaceable (note) vesa : video electronics standards association dpms : display power management signaling ddc1 : display data channel 1 ddc2b: display data channel 2b applications ? desk-top type of pc ? engineering workstation ? display terminals for control system ? monitors for process controller on screen display regarding the use of osd, please note that there is possibility of conflicts with a patent in europe and the u.s. thus, if such conflict might happen when you use osd, we shall not be responsible for any trouble. www..net www..net
data sheet en0456ej1v0ds00 2 nl10276ac28-02l structure and functions a color tft (thin film transistor) lcd module is comprised of a tft liquid crystal panel structure, lsis for driving the tft array, and a backlight assembly. the tft panel structure is created by sandwiching liquid crystal material in the narrow gap between a tft array glass substrate and a color filter glass substrate. after the driver lsis are connected to the panel, the backlight assembly is attached to the backside of the panel. rgb (red, green, blue) data signals from a source system is modulated into a form suitable for active matrix addressing by the onboard signal processor and sent to the driver lsis which in turn addresses the individual tft cells. acting as an electro-optical switch, each tft cell regulates light transmission from the backlight assembly when activated by the data source. by regulating the amount of light passing through the array of red, green, and blue dots, color images are created with clarity. outline of characteristics (at room temperature) display area 285.696 (h) 214.272 (v) mm drive system a-si tft active matrix display colors full-color number of pixels 1024 (h) 768 (v) pixel arrangement rgb vertical stripe pixel pitch 0.279 (h) 0.279 (v) mm module size 330.0 (h) 255.0 (v) 23.3 (d) mm (typ.) weight 1530 g (typ.) contrast ratio 150:1 (typ.) viewing angle (more than the contrast ratio of 10:1) ? horizontal : 85 (typ., left side, right side) ? vertical : 85 (typ., up side, down side) designed viewing direction ? optimum grayscale ( g = 2.2): perpendicular color gamut 40% (typ., at center, to ntsc) response time 34 ms (typ.), black 100% to white 10% luminance 200 cd/m 2 (typ.) input signals analog rgb signals, synchronous signals (hsync and vsync or composite) backlight edge light type: four cold cathode fluorescent lamps with an inverter lamp holder : 141lhs11 inverter : 150pw011 supply voltage 12 v, 12 v (logic/lcd driving, backlight) power consumption 25.1 w (typ.) www..net www..net data sheet en0456ej1v0ds00 3 nl10276ac28-02l block diagram lcd module r g b amp control signal on/off inverter gnd v ddb (+12 v) gndb clk v-driver backlight h-driver 3840 lines lcd panel 1024 lines h: 1280 3 (r, g, b) v: 1024 ledon ledoff sel up down exit left right reset menusel i/f signal recognition control signal osd hs/cs vsync pll aif timing controller dc/dc converter v dd (+12 v) sync. signal hs : hsync cs : composite synchronous signal note : neither gnd nor gndb is connected to frame. these should be connected in customer equipment. www..net www..net data sheet en0456ej1v0ds00 4 nl10276ac28-02l specifications general specifications item contents unit module size 330 0.5 (h) 255.0 0.5 (v) 24.5 (max.) (d) mm display area 285.696 (h) 214.272 (v) mm number of dots 1024 3 (h) 768 (v) dots pixel pitch 0.279 (h) 0.279 (v) mm dot pitch 0.093 (h) 0.279 (v) mm pixel arrangement rgb (red, green, blue) vertical stripe C display colors full color color weight 1,600 (max.) g absolute maximum ratings parameter symbol rating unit remarks v dd C0.3 to + 14 v supply voltage v dd b C0.3 to + 14 v t a = 25c logic input voltage v in1 C0.3 to + 5.5 v r,g,b input voltage v in2 C6.0 to + 6.0 v t a = 25c v dd = 12 v storage temp. tst C20 to + 60 c C operating temp. top 0 to 50 c module surface note 95% relative humidity ta 40c 85% relative humidity 40 < ta 50c humidity (no condensation) absolute humidity shall not exceed t a = 50c, 85 % relative humidity) level. ta > 50c note measured at the lcd panel (including self-fever) www..net www..net data sheet en0456ej1v0ds00 5 nl10276ac28-02l electrical characteristics (1) logic, lcd driving, backlight (t a = 25c) item symbol min. typ. max. unit remarks v dd 11.4 12.0 12.6 v logic and lcd driving supply voltage v dd b 11.4 12.0 12.6 v backlight logic input l voltage v il 0C0.8v logic input h voltage v ih 2.2 C 5.25 v hs/cs, vsync, sel, up, down, sel, reset, exit, right, left, ddcclk, ddcdat logic output l voltage v ol CC0.4v logic output h voltage v oh 2.4 C C v ddcdat logic input l current i il C1 C C m a logic input h current i ih CC1 m a hs/cs, vsync logic output l current 1 i ol1 CC1 m a logic output h current 1 i oh1 C1 C C m a ddcdat C 630 900 ma vdd = 12.0 v i dd C 170 200 ma power saving mode vdd = 12.0 v C 1460 1600 ma vddb = 12.0 v (max. luminance) supply current i dd b C 0.3 10 ma power saving mode vddb = 12.0 v (2) video signal (r, g, b) input (t a = 25c) item min. typ. max. unit remarks maximum amplitude (white - black) 0 (black) 0.7 (white) *a vp-p note dc input level (black) - 0.5 C +2.5 v C sync level 0.2 0.3 *b (0.6) vp-p g terminal (sync on green) *a + *b C C 1.1 vp-p C note contrast adjustment is needed if the amplitude exceeds 0.7 vp-p. www..net www..net data sheet en0456ej1v0ds00 6 nl10276ac28-02l power supply design (1) please note that the supply voltage must not be applied while the control signals (sel, up, down, exit, left, right and reset) are connected to gnd. otherwise the module may cause malfunction. (2) if the power supply voltage is applied while up and down are connected to gnd, the input control signals become ineffective mode. to reset this mode, turn off the power once and turn on the power while up and down are connected to gnd. then, the mode will be released. (3) do not change menusel setting while the module is operated. menusel selection (hierarchical type or toggle type) is set when the power supply voltage is applied. (4) inverter current wave inverter current wave is as follows. 1460 (ma) 0 (ma) luminance control frequency duty maximum luminance control: 100 % (duty) minimam luminance control: 20 % (duty) luminance control frequency input vsync frequency k input vsync frequency 75 hz: k = 4.6 input vsync frequency > 75 hz: k = 3.6 = (5) ripple of supply voltage please note that the ripple at the input connector of the module should be within the values shown in this table. it the ripple is beyond these values, the noise may appear on the screen. v dd (for logic and lcd driver) v dd b (for backlight) acceptable range 100 mvp-p 200 mvp-p note the acceptable range of ripple voltage includes spike noise. example of the power supply connection a) separate the power supply b) put the filter power v dd power v dd b filter* v dd filter* v dd b power filter* (reference value) l = 10 m h to 100 m h c = 10 m f to 100 m f (6) v dd b should be started up within 300 ms, otherwise, the protection circuit makes the backlight turn off. www..net www..net data sheet en0456ej1v0ds00 7 nl10276ac28-02l interface pin connections (1) logic and lcd driving cn1 part no. : 1-353119-4 adaptable socket: 1-353068-4 supplier : japan amp ltd. pin no. symbols pin no. symbols 1b8vsync 2gnd9gnd 3g10hs/cs 4gnd11gnd 5 r 12 ddcclk 6 gnd 13 n.c. 7 gnd 14 ddcdat 1 2 13 14 figure from socket view note 1: n.c. (no connection) must be open. cn3 part no. : df14a-25p-1.25h adaptable socket: df14-25s-1.25c supplier : hirose electric co., ltd. pin no. symbols pin no. symbols 1 ledon 14 exit 2ledoff15 gnd 3 gnd 16 n.c. 4n.c.17gnd 5n.c.18gnd 6 right 19 menusel 7left20n.c. 8 reset 21 n.c. 9 n.c. 22 n.c. 10 gnd 23 gnd 11 sel 24 n.c. 12 up 25 n.c. 13 down 12 25 24 figure from socket view note 1: n.c. (no connection) must be open. www..net www..net data sheet en0456ej1v0ds00 8 nl10276ac28-02l cn5 part no. : il-z-8pl-smty adaptable socket: il-z-8s-s125c3 supplier : japan aviation electronics industry limited (jae) pin no. symbols pin no. symbols 1v dd 5gnd 2v dd 6gnd 3v dd 7gnd 4v dd 8gnd 87 21 figure from socket view (2) backlight cn201 part no. : il-z-11pl-smty adaptable socket: il-z-11s-s125c3 supplier : japan aviation electronics industry limited (jae) pin no. symbols pin no. symbols 1v dd b 7 n.c. 2v dd b 8 n.c. 3v dd b 9 n.c. 4 gndb 10 n.c. 5 gndb 11 n.c. 6 gndb 11 10 1 2 figure from socket view note 1: n.c. (no connection) must be open. 1 cn1 8 cn5 1 1 cn3 25 1 11 cn201 14 rear view www..net www..net data sheet en0456ej1v0ds00 9 nl10276ac28-02l pin function symbol i/o logic description hs/cs input negative horizontal synchronous signal input or composite synchronous signal input (ttl level), positive/negative auto recognition vsync input negative vertical synchronous signal input (ttl level) positive/negative auto recognition, clock input for ddc1 r input C red video signal input (0.7 vp-p, input impedance 75 w ) g input C green video signal input (0.7 vp-p, input impedance 75 w ) b input C blue video signal input (0.7 vp-p, input impedance 75 w ) ledon output positive indicator for led power on h: led select, l: other status ledoff output positive indicator for power save mode h: power mode select, l: other status ddcclk input positive clk for ddc2b ddcdat input/ output positive data for ddc1/2b read/write sel input negative control function select signal (ttl level) sel is pulled up in the module. detail of the functions are mentioned in control functions . h or open: sel off, l: sel on up input negative control signal (ttl level) the signal increases the value of the functions selected. up is pulled up in tha module. h or open: up off, l: up on down input negative control signal (ttl level) the signal decreases the value of the functions selected. down is pulled up in the module. h" or open: down off, l : down on exit input negative control function exit signal (ttl level) exit is pulled up in the module. h" or open: exit off, l: exit on right note1 input negative control signal (ttl level) the signal increases the value of the functions selected. right is pulled up in the module. h or open: right off, l: right on left note1 input C control signal (ttl level) the signal decreases the value of the functions selected. left is pulled up in the module. h or open: left off, l: left on reset note1 input C control signal (ttl level) the signal initializes the selected function. reset is pulled up in the module. h or open: reset off, l: reset on menusel input C osd design select signal (ttl level) menusel is pulled up in the module. h or open: hierarchical type l: toggle type for detail, see osd menu select . www..net www..net data sheet en0456ej1v0ds00 10 nl10276ac28-02l symbol i/o logic description v dd C C power supply for logic and lcd driving +12 v ( 5%) v dd b C C power supply for backlight +12 v ( 5%) gnd C C ground for system gndb C C ground for backlight note 1 : this terminal becomes effective only when the value of button sel is 7. detail of the functions is mentioned in initial value change functions . note 2 : ground for system (gnd) and backlight (gndb) are not connected in the module. [osd menu select] osd menu type hierarchical type toggle type menusel h or open l how to adjust for details, see initial value change fucntion . menu brightness clock position contrast auto adjust for details, see initial value change fucntion . note 1 : if osd menu type is changed, the adjustment of the type becomes default value. then, it takes 5 seconds to display the changed menu after the supply voltage is input again. and, indicator for both ledon and ledoff are on at one time during the 5 seconds. note 2 : the initial value of contrast ratio is as follows. hierarchical type : 128:1 (typ.) toggle type : 100:1 (typ.) note 3 : on screen display regarding the use of osd, please note that there is possibility of conflicts with a patent in europe and the u.s. thus, if such conflict might happen when you use osd, we shall not be responsible for any trouble. www..net www..net data sheet en0456ej1v0ds00 11 nl10276ac28-02l [equivalent circuit] symbol i/o equivalent circuit ledon ledoff output rn2306 (toshiba) or equivalent output data sheet en0456ej1v0ds00 12 nl10276ac28-02l input signals input synchronous signal this module is corresponding to the synchronous signals below. synchronous signal auto recognition mode hs/cs vsync sync. on green separate synchronous signal mode (hs, vsync) input input input or no input composite synchronous mode input (cs) no input input or no input sync. on green mode no input no input input input (hs) no input input or no input no input input input or no input power saving mode no input no input no input note 1 : power saving mode corresponds to vesa dpma. note 2 : the module recognizes sync on green signal automatically, when the func in sog sel of sel data is y. refer to initial value change function . in case of sync on green mode, input signals (r, g, b, sync on green) must be inputted before power on. preset timing the 14 types of display timing shown below are preset in this module. the input synchronous signals are automatically recognized. preset no. display size vsync (hz) hsync (khz) system clk (mhz) v pulse (h) v b.porch (h) h pulse (clk) h b.porch (clk) sync logic v, h remarks 1 640 400 56.432 24.830 21.053 8 25 96 48 C,C * 2 640 480 59.992 31.469 25.175 2 33 96 48 C,C vga 3 720 400 70.087 31.469 28.322 2 35 108 45 +,C vga txt 4 800 600 60.317 37.879 40.000 4 23 128 88 +,+ vesa 5 640 480 66.667 35.000 30.240 3 39 64 96 song macintosh 6 640 480 75.000 37.500 31.500 3 16 64 120 C,C vesa 7 720 400 85.039 37.927 35.500 3 42 36 144 +,C vesa 8 640 480 85.008 43.269 36.000 3 25 48 112 C,C * 9 1024 768 60.004 48.363 65.000 6 29 136 160 C,C vesa 10 800 600 75.000 46.875 49.500 3 21 80 160 +,+ vesa 11 832 624 74.565 49.735 57.283 3 39 64 224 song macintosh 12 800 600 85.061 53.674 56.250 3 27 64 152 +,+ * 13 1024 768 70.069 56.476 75.000 6 29 136 144 +,+ vesa 14 1024 768 75.029 60.023 78.750 3 28 96 176 +,+ vesa * out of specification. www..net www..net data sheet en0456ej1v0ds00 13 nl10276ac28-02l note 1. even if the preset timing is entered, a little adjustment of the functions such as horizontal period, clk- delay and display position, are required. the adjusted values are memorized in every preset no. note 2. this module recognizes the synchronous signals with near preset timing of the frequency of hs, vsync, even in the case that the signals other than the preset timing that were entered. for instance, it is displayed with presetting number 6 in the case of 640 480 dot, hs: 37.861khz, vsync: 72.809 hz an example). please note that using out of the preset timings may cause wrong magnification ratio, unfitness of control functions or other improper display. note 3. the display color scale may be different between sync on green input and others. control functions expansion function expansion mode is a function to expand the screen size in different resolutions. for example, vga signal has 640 480 pixels. but, if the display data can be expanded to 1.6 times vertically and horizontally, vga screen image can be displayed fully on the screen of xga resolution. this module automatically recognizes the timing shown in preset timing as an expansion mode. please adopt this mode after evaluating display quality because the appearance in expansion mode may become bad in some cases. the followings show display magnifications for each mode. magnification input display number of pixels vertical horizontal xga 1024 768 1.0 1.0 svga 800 600 1.25 1.25 vga 640 480 1.6 1.6 vga text 720 400 1.92 / 1.6 hiearchical / toggle 1.42 mac 832 624 1.2 1.2 www..net www..net data sheet en0456ej1v0ds00 14 nl10276ac28-02l data sheet en0456ej1v0ds00 15 nl10276ac28-02l ddc function this function is corresponding to vesa ddc tm and edid tm (structure version 1). follow the specifications of the ic when you write data. then vclk should be fixed on h. please write a data into necessary addresses in advance when you use this function. data 55h in address 00h and ffh in other address are already programmed when shipping. the input equivalent circuit diagram is as follow. edid: extended display identification data data sheet en0456ej1v0ds00 16 nl10276ac28-02l control function items no. form function items 1 auto adjust clock and position auto adjust 2 brightness brightness of backlight control h. size horizontal display period adjust 3clock clock phase clk-phase adjust h. position horizontal position adjust 4position v. position vertical position adjust w, r, g, b white-level of video signals synchronous color and each color control 5 contrast w white-level of video signal synchronous color control w, r, g, b color-level of video signals synchronous color and each color control 6 color level w color-level of video signal synchronous color control 7 information video signal information display multi-scan function, hsync and vsync frequency 8 osd position osd position adjust the display position of osd can be moved. 9 config sync on green signal. response or non-response to sync on green signal is selected. when non-response is selected by initial value change functions , config is not displayed. 10 all reset reset to initial value. the values in no. 1 to no. 6, no. 8 and no. 9 are returned to the initial values. in order to achieve the best picture quality, the above functions should be adjusted by setting sel, up, down, left, right, reset and exit signals. each adjusted value is memorized as soon as sel is selected or time out mode is valid and the memorized values are not affected even if the power is switched off. but the selected value is not memorized in case that a selected mode is changed to another one before time out or power is turned off before time out. www..net www..net data sheet en0456ej1v0ds00 17 nl10276ac28-02l flow chart of control functions (1) hierarchical type (4 switches used for adjustment; sel, up, down and exit) * for details, see initial value change functions C 6. sel data, button sel - menu auto adjust brightness clock position contrast menu auto adjust brightness clock position contrast start (sel): osd opens (exit): osd closes (exit), (sel) (sel) auto adjust no yes (down) (up) (exit) auto adjust no yes (up), (down) - (up), (down) (sel): auto adjust brightness (exit): osd closes (exit) (sel) reset brightness no yes (sel) - (sel), (exit) (up), (down)) - (up), (down)) (up), (down) (down) (up) continue to next page www..net www..net data sheet en0456ej1v0ds00 18 nl10276ac28-02l (down) (up) (down) (up) menu auto adjust brightness clock position contrast reset brightness no yes (up), (down)) - (up), (down)) (exit): cancel (sel): initialize (exit): osd closes (exit) (sel) (sel) - (exit) h. size clock phase h. size clock phase h. size clock phase (up) / (down) (sel): reset h. size similar behavior as that of ?. size?adjustment shown above. (exit) (up), (down) (up), (down) menu auto adjust brightness clock position contrast (exit): osd closes (down) (up) (exit) (sel) h. position v. position similar behavior as that of ?lock?adjustment shown above. continue to next page www..net www..net data sheet en0456ej1v0ds00 19 nl10276ac28-02l (exit): osd closes (down) (up) (exit) (sel) menu auto adjust brightness clock position contrast (down) - (up) w r g b [s-cnt sel is on] (sel), (up), (down), (exit) for details, see initial value change functions ?. sel data ? [s-cnt sel is off] (up) / (down) contrast w contrast (exit): osd closes (down) (up) (exit) (sel) w r g b [s-lvl sel is on] (sel), (up), (down), (exit) for details, see initial value change functions ?. sel data ? [s-cnt sel is off] (up) / (down) color level w color level menu color level information osd position config all reset menu color level information osd position config all reset (exit): osd closes (exit) (sel) (down) (up) continue to next page * * www..net www..net data sheet en0456ej1v0ds00 20 nl10276ac28-02l (down) (up) menu color level information osd position config all reset menu color level information osd position config all reset menu color level information osd position config all reset * * * (down) (up) (down) (up) information 1024 788 hf 60.0 khz vf 75.0 khz (sel) (exit) (exit): osd closes (exit) (sel) osd position center (up) / (down): osd position select center/leftup/rightup/ leftdown/rightdown ? t (sel): reset osd position (exit): osd closes (exit) (sel) sync on green off (up) / (down): select ?ync on green acceptability [on/off] (sel): reset sync on green (exit): osd closes (exit) (sel) all reset no yes config is not indicated, when sog sel selected menu ??by initial value change functions ?. sel data ? * all reset no yes (up), (down) - (up), (down) (sel): all reset (exit) www..net www..net data sheet en0456ej1v0ds00 21 nl10276ac28-02l (2) hierarchical type (7 switches used for adjustment; sel, up, down, exit, left, right and reset) * for details, see initial value change functions C 6. sel data, button sel - menu auto adjust brightness clock position contrast menu auto adjust brightness clock position contrast start (sel): menu open (exit): osd closes (exit), (sel) (sel) auto adjust no yes (down) (up) (exit) auto adjust no yes (left), (right), (up), (down) - (left), (right), (up), (down) (sel): auto adjust brightness (exit): osd closes (exit) (sel) reset brightness no yes (reset) - (sel), (exit) (left), (right) (down) (up) continue to next page (left), (right), (up), (down) - (left), (right), (up), (down) www..net www..net data sheet en0456ej1v0ds00 22 nl10276ac28-02l (down) (up) (down) (up) menu auto adjust brightness clock position contrast reset brightness no yes (exit): cancel (sel): initialize (exit): osd closes (sel) (up), (down) - (up), (down) h. size clock phase h. size clock phase (left) / (right) (reset): reset h. size (left) / (right) (reset): reset clock phase (exit) menu auto adjust brightness clock position contrast (exit): osd closes (down) (up) (exit) (sel) position (left) / (right) / (up) / (down) (reset): reset position [h.position and v.position] continue to next page (exit) (left), (right), (up), (down) - (left), (right), (up), (down) www..net www..net data sheet en0456ej1v0ds00 23 nl10276ac28-02l (exit): osd closes (down) (up) (exit) (sel) menu auto adjust brightness clock position contrast (down) - (up) w r g b [s-cnt sel is on] (sel), (up), (down), (left) / (right), (exit), (reset) for details, see initial value change functions ?. sel data ? [s-cnt sel is off] (right), (up) / (left), (down) contrast w contrast (exit): osd closes (down) (up) (exit) (sel) w r g b [s-cnt sel is on] (sel), (up), (down), (left) / (right), (exit), (reset) for details, see initial value change functions ?. sel data ? [s-cnt sel is off] (right), (up) / (left), (down) color level w color level menu color level information osd position config all reset menu color level information osd position config all reset (exit): osd closes (exit) (sel) (down) (up) continue to next page * * www..net www..net data sheet en0456ej1v0ds00 24 nl10276ac28-02l (down) (up) menu color level information osd position config all reset menu color level information osd position config all reset menu color level information osd position config all reset * * * (down) (up) (down) (up) information 1024 788 hf 60.0 khz vf 75.0 khz (sel) (exit) (exit): osd closes (exit) (sel) osd position center (left) / (right) / (up) / (down): osd position selects center/leftup/rightup/ leftdown/rightdown ? t (sel): reset position (sel): reset osd position (exit): osd closes (exit) (sel) sync on green off (left) / (light) / (up) / (down): sync on green select [on/off] (sel): reset sync on green (exit): osd closes (exit) (sel) all reset no yes config is not indicated, when sog sel selected menu ??by initial value change functions ?. sel data ? * all reset no yes (left), (right), (up), (down) - (left), (right), (up), (down) (sel): initialized (exit) www..net www..net data sheet en0456ej1v0ds00 25 nl10276ac28-02l note 1 : the value of the selected signals by left, right, up and down key is continuously increased if the input signal is held for more than approx. one second. if its less than one second, the value is increased by one. note 2 : reset signal initializes the value selected by sel key. all reset function initializes all the values adjusted before. note 3 : no key input for more than ten seconds shall be regarded as time out. note 4 : contrast w is synchronous with contrast r, contrast g and contrast b. note 5 : color level w is synchronous with color level r, color level g and color level b. www..net www..net data sheet en0456ej1v0ds00 26 nl10276ac28-02l (3) toggle type (sel, up, down and exit) (up), (down): + or - (exit): initialize start (sel) (up), (down) (exit) (sel) (up), (down) (exit) (sel) (up), (down) (exit) (sel) (up), (down) (exit) (sel) (up), (down) (exit) (sel) (up), (down) (exit) (sel) (exit) all reset press reset key over 2 seconds (sel) osd closes note 1 : the value of the selected signals by up and down key is continuously incremented if the input signal is held for more than approx. one second. note 2 : reset signals initializes the value selected by sel key. all reset function initializes all the values adjusted before. note 3 : no key input for more than five seconds shall be regarded as time out. note 4 : exit is valid when connected to gnd for more than approx. two seconds. www..net www..net data sheet en0456ej1v0ds00 27 nl10276ac28-02l initial value change functions initial value, osd items, etc. can be changed. the changed initial value becomes initial value in each preset timing, and is applicable when it is reset (including all reset). ? how to transpose to initial value change mode. hierarchical type : connect set and up to gnd at the same time when osd function is in information mode. toggle type : connect sel to gnd while sel is connected to gnd when osd function is in all reset mode. ? operation sel, up, down, and exit ? how to return to normal mode connect exit to gnd or turn off power supply when osd is closed. both ledon and ledoff become h when this mode is operating. no. form function items 1 compatible it becomes valid when toggle menu type is selected only. yes : sync on green the initial value of contrast (rgb synchronous) becomes 128. no : no sync on green the initial value of contrast (rgb synchronous) becomes 100. the nec factory value: no. 2 brightness the maximum value of brightness of backlight can be changed. initial value: 100 3 color level the initial value of color level can be changed. initial value: 128 4 contrast the initial value of contrast can be changed. initial value: 128 (when no is selected by compatible in toggle menu type, the initial value of rgb synchronous only is 100. as for rgb synchronous, this clause setup value becomes valid as the initial value regardless of the selections state of compatible.) mode no. of preset timings is displayed. hse the initial value of the double value can be changed. delay the value of the clk delay can be changed. (initial value can not be changed.) initial value: 0 vd the initial value of the up-down position of the display position can be changed. hd the initial value of the left-right position of the display position can be changed. auto adjust auto adjust par. delay the compensation value of delay of the auto adjust can be changed. valid range: 0 to 255 5 lcd data par. hd the compensation value of horizontal position of the auto adjust can be changed. valid range: 0 to 127 continue to next page www..net www..net data sheet en0456ej1v0ds00 28 nl10276ac28-02l no. form function items 5 lcd data lcd reset the values in no. 5 lcd data are returned to the nec factory values. 6 sel data s C lvl sel the adjustment that rgb is independent can be made impossible by the adjustment of the color level. in this case, the adjustment item that rgb is independent is not displayed on the menu screen. on : independent adjustment is available. off : independent adjustment is impossible initial value: on. s C cnt sel the adjustment that rgb is independent can be made impossible by the adjustment of the color level. in this case, the adjustment item that rgb is independent is not displayed on the menu screen. on : independent adjustment is available. off : independent adjustment is impossible initial value: on. sog sel select or non-select of sync on green and display or non-display of select menu are selected. when non-display selected, config is not displayed. ? func (y: for sync on green select) (n: for sync on green non-select) ? menu (y: select menu display.) (n: select menu non-display.) initial value: y/n * it becomes effective only when the hierarchical menu type is selected. but it becomes invalid when toggle menu type is selected. menu sel b (blue) or s (transparency) can be selected for the background color of the osd menu. initial value: b button sel 4 (sel, up, down and exit) or 7 (sel, up, dpwn, right, left, exit and reset) number of adjust switch are selected. initial value: 7 psosd sel display or no display for power save osd can be selected. (for detail, see informarion display by osd ) on: display off: no display initial value: off 7 information input signal information is displayed. 8 osd position the initial value of osd display position can be changed. c: center ul: upper left ur: upper right dl: down left dr: down right initial value: c 9 used time use time in normal and power save state is displayed. use time is recorded in every five minutes. but it is not recorded when power supply is cut off within five minutes. 10 full reset all value is returned to nec factory value. it takes about seven seconds. * the value of no.5 lcd data are memorized in every preset timing. * selected adjust item is displayed with osd. * data except auto adjust of 5. lcd data are saved at the moment when it was returned in the extreme upper menu. but it is not kept when the power supply is cut off halfway. * all adjust value is returned to the nec factory value when menu type is changed. * evaluate compensation value of par. delay and par. hd of no.5 lcd data, and be decided. www..net www..net data sheet en0456ej1v0ds00 29 nl10276ac28-02l informarion display by osd 1. power save : frequency of horizontal, vertical synchronous signal is displayed for four seconds at the time of the power save mode switchover. power save hf 0.0 khz vf 0.0 khz * it is displayed when horizontal synchronous signal frequency (hf) and vertical synchronous signal frequency (vf) are the following. (1) hf < 10 khz (2) vf < 40 hz (3) (1) and (2) * it is not displayed when power save osd no display form is selected with initial value change functions - 6. sel data, psosd sel -. 2. out of range : each frequency is displayed for four seconds when the horizontal and vertical synchronous signal outside the corresponding range is inputted. out of range hf 64.0 khz vf 60.0 khz * it is displayed when horizontal synchronous signal frequency (hf) and vertical synchronous signal frequency (vf) are the following. (1) 10 khz hf < 23 khz or 61.5 khz < hf (2) 40 hz vf < 50 hz or 200 hz < vf (3) (1) and (2) but it is not displayed when either hf or vf is power save mode. * display or no display for out of range can not be selected. 3. disable : it is displayed for four seconds that the switch for adjust is disable. key disable www..net www..net data sheet en0456ej1v0ds00 30 nl10276ac28-02l input signal and display position - xga standard timing - pixels d (0,0) d (0,1) d (0,2) ? ? ? ? ? ? d (0,1023) d (1,0) d (1,1) d (1,2) ? ? ? ? ? ? d (1,1023) d (2,0) d (2,1) d (2,2) ? ? ? ? ? ? d (2,1023) ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? d (767,0) d (767,1) d (767,2) ? ? ? ? ? ? d (767, 1023) tvb tvp vsync 1 line hsync xga mode (vd = ?5? invalid valid d (0, x), d (1, x), d (2, x) ? 012345 353637 thb thp hsync 1 clk r clk xga mode (hd = ?96? invalid valid d (x, 0), d (x, 1), d (x, 2) ? 012345 296297298 tda b g r b g note the tda should be more than 4ns www..net www..net data sheet en0456ej1v0ds00 31 nl10276ac28-02l optical characteristics (ta = 25c, v dd = 12 v, v dd b = 12 v, note 1 ) item symbol condition min. typ. max. unit remark contrast ratio cr q r = 0 , q l = 0 , q d = 0 , white/black, at center 80 150 -- note 2 luminance lvmax white, at center 150 200 - cd/m 2 note 3 luminance uniformity - white - C1.30 - note 4 reference data (ta = 25c, v dd = 12 v, v dd b = 12 v, note 1 ) item symbol condition min. typ. max. unit remark contrast ratio cr best contrast angle q r = 0 , q l = 0 , q d = 5 white/black, at center - 300 - note 2 color gamut c q r = 0 , q l = 0 , q u = 0 , q d = 0 at center, to ntsc 35 40 - % - q r7085 - deg. q l cr > 10, q u = 0 , q d = 0 white/black, at center 70 85 - deg. q u7085 - deg. viewing angle range q d cr > 10, q r = 0 , q l = 0 white/black, at center 70 40 - deg. note 4 ton black to white - 34 80 response time toff white to black - 40 80 ms note 6 note 1. the luminance is measured after 20 minutes from the module works, with all pixels in white. the typical value is measured after luminance saturation. display mode: vesa xga-75 hz rgb input voltage: 0.7 vp-p contrast: default note 2. the contrast ratio is calculated by using the following formula. luminance with all pixels in white contrast ratio (cr) = luminance with all pixels in black note 3. the luminance is measured after 20 minutes from the module works, with all pixels in white. the typical value is measured after luminance saturation, more than one hour after burn-in. the timing is xga standard mode, preset no. 9. 50 cm 1 lcd module photo-detector (topcon bm-5a) www..net www..net data sheet en0456ej1v0ds00 32 nl10276ac28-02l note 4. luminance uniformity is calculated by using the following formula. maximum luminance luminance uniformity = minimum luminance the luminance is measured at near the five points shown below. 256 512 768 192 384 576 1 4 3 5 2 column row note 5. definitions of viewing angle are as follows. ? ? d q l q u q r q +y +x 12 o?lock perpendicular note 6. definitions of response time is as follows. photo-detector output signal is measured when the luminance changes black to white or white to black. white black luminance 90 % 0 % 10 % 100 % ton toff www..net www..net data sheet en0456ej1v0ds00 33 nl10276ac28-02l reliability test test item test condition judgment high temperature/humidity operation 50 2 c, 85% relative humidity 240 hours, display data is black. note 1 heat cycle (operation) <1> 0 c 3 c 1 hour 55 c 3 c 1 hour <2> 50 cycles, 4 hours/cycle <3> display data is black. note 1 thermal shock (non-operation) <1> - 20 c 3 c 30 minutes 60 c 3 c 30 minutes <2> 100 cycles <3> temperature transition time is within 5 minutes. note 1 vibration (non-operation) <1> 5-100 hz, 19.6 m/s 2 (2g) 1 minute/cycle, x, y, z direction <2> 50 times each direction notes 1, 2 mechanical shock (non-operation) <1> 294 m/s 2 (30g), 11 ms x, y, z direction <2> 3 times each direction notes 1, 2 esd (operation) 150 pf, 150 w , 10 kv 9 places on a panel note 3 10 times each place at one-second intervals note 1 dust (operation) 15 kinds of dust (jis-z 8901) hourly 15 seconds stir, 8 times repeat note 1 notes 1. display function is checked by the same condition as lcd module out-going inspection. 2. physical damage. 3. discharge points are shown in the figure. www..net www..net data sheet en0456ej1v0ds00 34 nl10276ac28-02l general cautions because next figures and sentences are very important, please understand these contents as follows. caution this figure is a mark that you will get hurt and/or the module will have damages when you make a mistake to operate. this figure is a mark that you will get an electric shock when you make a mistake to operate. this figure is a mark that you will get hurt when you make a mistake to operate. caution do not touch an inverter - - on which is stuck a caution label - - while the lcd module is under the operation, because of dangerous high voltage. (1) caution when taking out the module a pick the pouch only, in taking out module from a carrier box. (2) cautions for handling the module a) as the electrostatic discharges may break the lcd module, handle the lcd module with care against electrostaic discharges. b) as the lcd panel and backlight element are made from fragile glass material, impulse and pressure to the lcd module should be avoided. c) as the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. d) do not pull the interface connectors in or out while the lcd module is operating. e) put the module display side down on a flat horizontal plane. f) handle connectors and cables with care. g) when the module is operating, do not lose clk, hs or vsync signal. if any one of these signals is lost, the lcd panel would be damaged. h) the torque to mounting screw should never exceed 0.392 nm (4 kgfcm). (3) cautions for the atmosphere a) dew drop atmosphere should be avoided. b) do not store and/or operate the lcd module in a high temperature and/or high humidity atmosphere. storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. c) this module uses cold cathod fluorescent lamps. therefore, the life of lamps becomes short if the module is operated under the low temperature environment. d) do not operate the lcd module in a high magnetic field. (4) caution for the module characteristics a) do not apply the fixed pattern for a long time to the lcd module. applying fixed pattern for a long time may cause image sticking. www..net www..net data sheet en0456ej1v0ds00 35 nl10276ac28-02l (5) other cautions a) do not disassemble and/or reassemble lcd module. b) do not readjust any variable resistors or switches in the module. c) when returning the module for repair or etc., please pack the module properly to avoid any damages. we recommend using the original shipping packages. liquid crystal display has the following specific characteristics. there are not defects nor malfunctions. the display condition of lcd module may be affected by the ambient temperature. the lcd module has cold cathode tube for backlight. optical characteristics, like luminance or uniformity, will change during time. uneven brightness and/or small spots may be noticed depending on different display patterns. www..net www..net data sheet en0456ej1v0ds00 36 nl10276ac28-02l outline drawings front view (unit in mm) 330 ?.5 320 ?.3 290.4 ?.3 (bezel opening) 4.5 4.5 160 ?.7 4.5 4.5 13 80 13 94 13 72 13 20 30 55 4.7 4.5 ?.2 f 4? 3.5 ?.2 f active area center 200 ?.3 5 92.8 5 5 100 ?.7 9.5 ?.3 200 ?.3 32 ?.3 5 219 ?.3 (bezel opening) 255 ?.5 16.2 max 22 typ 20.8 285.696 (active area) 10.8 214.27 (active area) max 24.5 typ 23.3 4?.4 ?.3 4?.7 ?.3 ?the torque for mounting screw should never 0.392 n ?m (4 kg ?cm). ?not shown tolerance of the dimension is ?.5 mm. www..net www..net data sheet en0456ej1v0ds00 37 nl10276ac28-02l rear view (unit in mm) 11 cn201 1 serial: b9810036 panel: a100892018301 99.8.26/ c170832 made in japan model: nl10276ac28-02l a100892018301 material information light guide: >pmma< the tft color lcd panel contains cold cathode flourescest lamps. please follow localordinances or regulations for its disposal caution high voltage 52 30 100 30 32 ? 7 14.3 130 14.3 7 117 ? 231 152 199 ? 153 ? 54.5 ? 14 1 cn1 25 1 cn3 18 cn5 223 24 8 13.8 8 13.2 max 24.5 69.5 typ 23.3 14.3 54 31 48.6 109 18.3 20 10.3 3 3.4 ?.3 max 22 typ 20.8 16.2 10.3 69.3 ? 53 a 10.3 14.2 10.2 5.1 10.3 16.2 1 ?the torque for mounting screw should never exceed 0.392 n ?m (4 kg ?cm). ?not shown tolerance of the dimension is ?.5 mm. fpc www..net www..net data sheet en0456ej1v0ds00 38 nl10276ac28-02l [memo] www..net www..net data sheet en0456ej1v0ds00 39 nl10276ac28-02l [memo] www..net www..net nl10276ac28-02l data sheet no part of this document may be copied or reproduced in any form or by any means without the prior written consent of nec corporation. nec corporation assumes no responsibility for any errors which may appear in this document. nec corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. no license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec corporation or others. while nec corporation has been making continuous effort to enhance the reliability of its electronic components, the possibility of defects cannot be eliminated entirely. to minimize risks of damage or injury to persons or property arising from a defect in an nec electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. nec devices are classified into the following three quality grades: "standard", "special", and "specific". the specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. the recommended applications of a device depend on its quality grade, as indicated below. customers must check the quality grade of each device before using it in a particular application. standard: computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots special: transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) specific: aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. the quality grade of nec devices is "standard" unless otherwise specified in nec's data sheets or data books. if customers intend to use nec devices for applications other than those specified for standard quality grade, they should contact an nec sales representative in advance. anti-radioactive design is not implemented in this product. www..net www..net |
Price & Availability of NL102768AC28-02
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |